How do I calculate manure application rates?

Start with crop need and a manure test

BISMARCK, North Dakota — To calculate a manure application rate, you take what the crop needs, subtract what the soil and other sources already supply, then divide the remainder by the usable nutrient content of your manure, based on a lab test. The result is tons or gallons per acre. Add a limit based on phosphorus where your state requires one, and check it against the spreader's actual output.

The arithmetic is simple. The inputs are where people get into trouble. Here's the order to work in.

Step one: crop nutrient need

Find the recommended nitrogen, phosphorus and potassium for your crop and yield goal. Your state's land-grant university publishes recommendations, and your soil test lab will report them with its test. Use a realistic yield goal based on your own history, not your best year. Check extension resources or your state extension site for local methods.

Subtract credits. Soybeans or alfalfa before corn leave nitrogen credits, and soil tests with high phosphorus or potassium reduce or eliminate need for those. Previous manure applications also count. What's left is your nutrient requirement from manure and fertilizer.

Step two: know what's in the manure

Send a representative sample to a lab and ask for total nitrogen, ammonium nitrogen, phosphorus, potassium, and dry matter or moisture. Use the results from your own manure, not a table, whenever you can. Feed, bedding, storage method and age change content a lot.

Labs report results in different units: percent, pounds per ton, pounds per thousand gallons, or parts per million. Be careful with conversions, and ask the lab to report in pounds per ton or per thousand gallons, which are easier for field math. If unit conversions confuse you, ask your extension office to check your math.

Only part of the nitrogen is available in the first season. Ammonium nitrogen is quick, while organic nitrogen releases slowly over years. Application method matters because surface applications lose ammonia to the air, and incorporation or injection holds more. Your extension office has availability factors by manure type and method. Iowa State's Ag Decision Maker and Nutrient Stewardship can point you to calculators and guidance.

Step three: divide and compare

For each nutrient, take the amount needed and divide by the available nutrient per ton or per thousand gallons. That gives rates by nitrogen, phosphorus and potassium. Set the application by your plan's limiting nutrient. In many states that's nitrogen on fields with low phosphorus, and phosphorus on fields testing high.

Say a field needs a certain amount of nitrogen and the manure supplies a certain available amount per ton. Divide, and you have tons per acre. Then check phosphorus. If that rate puts on more phosphorus than the crop will remove or than your state's limit allows, cut the rate and supply the rest of the nitrogen from fertilizer or a legume credit.

Write the numbers on paper and have a second person check. A misplaced decimal can turn a plan into a pollution problem.

Step four: turn it into spreader settings

A rate on paper means little until the spreader delivers it. Calibrate your spreader to find out how much it applies per acre at a given gate setting, speed and overlap. Then adjust the settings to hit the target. If you haven't calibrated, you're guessing, and the guess is often off by a wide margin.

Account for variation in manure itself. Loads from the bottom of a pit differ from the top, so agitate liquid manure and sample during pumping. For solid manure, load consistently.

Re-test when something changes, such as new feed, a new bedding, a different storage pile or a switch in species.

Keep it legal and keep records

Check state rules for annual limits, setbacks from water, application on frozen or snow-covered ground, and slope restrictions. Your NRCS service center and state agriculture department can tell you what's required. If your farm has a nutrient management plan, rates should follow it.

After each application, record date, field, source, rate, method and weather. Compare to the plan. Over time, soil tests will show whether you're building or drawing down nutrients, and you can adjust. Records also protect you if a neighbor or inspector asks questions.

The short version

Crop need minus credits, divided by available manure nutrients, limited by phosphorus where required, then checked against a calibrated spreader. Test, calculate, calibrate, record. And yes, do the math twice. The spreader doesn't forgive rounding errors.