How do I calibrate a manure spreader?

Measure what it really puts down

HASTINGS, Nebraska — To calibrate a manure spreader, you measure how much manure it applies over a known area at a set speed, gate opening and PTO or conveyor setting, then adjust until it matches your target rate. Calibrating takes an hour or two and tells you the truth about a machine that's been guessing for years.

You need to calibrate for each manure type, because density and moisture change what comes out. Re-do it whenever the manure, equipment or settings change.

What you need before you start

Know your target rate. That comes from your nutrient plan, based on soil test, crop need and manure analysis. Then gather a scale, tarps or shallow catch pans, a tape measure, a stopwatch, flags or stakes, and a calculator. Weigh the empty spreader, or find a scale at a grain elevator, feed mill or landfill.

Choose a clean, level, safe area. Check the spreader over: chains, beaters, floor and gate. Worn parts distort results. Take safety seriously and keep shields in place. The OSHA agriculture page and NIOSH agriculture program have PTO and machine safety guidance.

The weigh method for solid spreaders

This is the most direct method. Weigh the empty spreader, then weigh it loaded. The difference is the load weight. Spread the load across a measured field strip, record the width of the spread pattern and the distance traveled until empty, then weigh the spreader again if you can to confirm.

Calculate acres covered: width in feet times length in feet, divided by the number of square feet in an acre. Then divide the load weight by acres. That gives tons or pounds per acre. Repeat with several loads, since manure varies from load to load. Average the results.

If the number is too high or low, change ground speed, gate opening or conveyor speed, and test again. A slower speed or larger gate opening increases the rate. Make one change at a time, so you know what worked.

The tarp method

To check both rate and uniformity, lay out tarps or pans at regular spacing across the width of the spread pattern. Drive over them at your normal speed and settings. Collect the manure from each, and weigh it. Compare amounts across the pattern.

You'll see how even the spread is. Many spreaders put more in the middle and less at the edges, or throw heavier to one side. The data tells you what overlap to use between passes, and whether beaters, shields or deflectors need work. Evenness matters as much as average rate, because uneven spreading means over-application in some strips and under-application in others.

Adjust the swath width, or overlap, until the combined pattern is reasonably even. Your extension office may have spreader calibration worksheets and videos. Search extension resources or your state extension site.

Calibrating liquid tankers

For tank spreaders, calibrate by volume. Know the tank's capacity. Fill it to a marked level, spread over a measured strip, and measure the distance until empty, or measure what's left. Calculate gallons per acre from the area covered. Flow meters on pumps and drag hose systems give direct readings, but check them against tank measurements. Meters need their own calibration.

For injectors and splash plates, check that the pattern is even and the speed consistent. Slurry thickness changes flow, so agitate before testing. Repeat for different pump settings and speeds, and record them.

Keep the settings and re-check

Write down the settings that produce each rate for each manure type, and keep the chart in the tractor cab. A taped-up card is better than memory. Re-check at the beginning of each season, after repairs, when manure consistency changes, and if you use a different tractor.

Wear changes output. Chains stretch, beaters wear, and gates stick. If results drift, adjust or replace parts. A well-maintained spreader holds its calibration longer.

Record your calibration results in your nutrient management records. If you're in a program that requires proof, they matter. NRCS and your conservation district can tell you what documentation applies.

The short version

Weigh or measure what comes out, compare to what you planned, adjust settings one at a time, test the pattern for evenness, and write down what works. Without calibration, the number on your plan is a wish. With it, you know what's actually on the ground.