How do I make brie at home?

A bloomy rind, step by step

MADISON, Wisconsin — You make brie by setting pasteurized milk with a mesophilic starter and a little rennet, adding a white-mold culture, ladling the soft curd gently into small molds, draining it for a day or two, salting, and then ripening the wheels in a cool, humid space for several weeks. The mold does the heavy lifting. Your job is to keep the milk clean, the curd unbroken and the ripening box from turning into a swamp or a desert. It isn't hard, but it is slow, and brie punishes impatience.

Start with the right milk

Brie wants whole milk, and richer milk gives a creamier paste. Use pasteurized milk that has not been ultra-high-temperature treated, because UHT milk often won't set. If you work with milk from your own animals, pasteurize it at home first or learn your state's rules for raw milk cheese before you sell a single wheel. Warm the milk to roughly 90 degrees Fahrenheit, which is the usual range for mesophilic starters, and add the starter culture. Many makers also add a pinch of calcium chloride if the milk is pasteurized, since heating weakens the curd. Let the starter work for about an hour before adding rennet, following the packet for dose.

Add the mold and set the curd

Brie gets its white rind from Penicillium candidum, often paired with a little Geotrichum candidum for texture. Buy these from a cheesemaking supplier, since the packets are sized for small batches. Stir the mold powder into the milk with the starter, or sprinkle it on top and let it rehydrate. Add diluted rennet, stir for a minute, and then stop moving the pot. The curd should set into a clean break in about an hour. Don't poke it to check every five minutes. A curd that is bumped while setting comes out shattered and wet.

Ladle, drain and salt

Cut the curd into large pieces, around an inch, and rest it for a few minutes. Then ladle it in thin layers into brie molds set on a draining mat. Thin layers matter, because a heavy scoop crushes the curd and leaves you with a dense wheel. The molds will look absurdly full at first. Within a day they sink to about a third of their height. Flip the wheels once or twice as they drain at room temperature, and when they are firm enough to hold their shape, unmold and salt the surface lightly, either by dry salt or a short brine.

Ripen with patience

Move the wheels to a ripening container with a rack, set in a refrigerator or cool room at roughly 50 to 55 degrees Fahrenheit. Aim for high humidity without dripping water on the cheese. Flip daily. White fuzz usually shows up in about a week and covers the wheel in another few days. Once it covers evenly, wrap the cheese in cheese paper and move it to a cold refrigerator, then let it ripen for a few more weeks. Brie is ready when it gives under a thumb like a ripe peach.

Troubleshooting

Keep notes on every batch, since milk changes with the season and the animal's diet. Extension programs such as Penn State Extension and the University of Wisconsin farm programs publish dairy processing guidance. If you plan to sell, read USDA AMS material on local and regional food, and check with your state department of agriculture about licensing.

Keep a make sheet

Brie rewards records more than most cheeses, because small changes show up weeks later. Write down the milk source, the starter and mold doses, the set time, how long the wheels drained and the humidity you held during ripening. When a wheel turns out especially good, you can repeat it. When one turns out chalky, you can look back and see what changed. Also label every wheel with a make date. A refrigerator full of anonymous white pucks gets confusing fast, and a ripe brie waits for no one. If you sell cheese, those same notes double as the batch records an inspector may ask for, so the habit pays twice.

Your first wheel probably won't win a ribbon, but it'll still be better than anything labeled brie-style at the gas station. Make a second batch in the same week and compare notes.