How do I reduce feed waste?

Find the leaks from field to bunk

NEW HOLSTEIN, Wisconsin — Reduce feed waste by measuring where it happens, then fixing the biggest leaks first. On most dairies those are silage storage and feedout, mixing and loading errors, and bunk management. Waste is quiet. It doesn't send a bill; it just shows up as feed you grew or bought that never reached a cow.

The good news is that most fixes are cheap. They need attention more than money.

Silage storage and the feed face

Silage losses start in the field and continue in the pile, bunker or bag. Poor packing leaves air in the silage, and air means heat, mold and spoilage. Slow feedout lets oxygen creep into the face, so the top and front of a pile can spoil before it's fed.

Practical steps include packing in thin layers, covering quickly and sealing the plastic with weighted edges, and removing enough from the face each day to stay ahead of spoilage. Cut a smooth, tight face rather than tearing it with a loader bucket, since a ragged face lets air deep into the pile. Check for water pooling on the cover and for holes made by birds or rodents.

University resources such as Penn State Extension and Wisconsin Extension publish silage management guides that cover packing, covering and feedout rates.

Hay and bagged feeds

Hay stored outside loses quality, especially where bales touch the ground or sit uncovered. Stack under cover or use a pad and tarp. Feed in a way that limits trampling: rings, feeders or racks for dry cows and heifers cut a lot of loss compared with unrolled bales.

Bagged and baled silage needs patching when it's punctured. A small hole turns into a spoiled section quickly. Walk the rows regularly and fix punctures.

Commodities stored in sheds or bins need attention too. Moisture, pests and leaks create losses that never show up in a feed budget. A related article covers commodity storage.

Mixing and loading

A mixer that overloads, under-mixes or loads out of order wastes feed and changes the ration. Check the scale regularly against known weights. Load in the order that works for your mixer, and avoid spills at loading time. Watch the mix: if cows are sorting, the mix may be too long, too dry or too wet.

Records help. If mixer software or a clipboard shows loads that drift from the ration, retrain the operator or recalibrate the scale. Small errors repeated every day add up to a large amount over a season.

Bunk management

Feed should be available when cows want to eat, and it should stay clean and fresh. Push feed up frequently, especially in the first hours after feeding, so cows can reach it. Remove refusals before they spoil, and don't let wet feed accumulate at the back of the bunk.

Aim for a small amount of leftovers, not zero and not a heap. Zero can mean some cows aren't getting enough. A heap means you're overfeeding or cows are sorting. Adjust the amount fed according to refusals, and weigh the leftovers when you can. Refusals can sometimes be fed to heifers or dry cows if they're clean and safe, but moldy feed shouldn't be fed to anything without advice from your vet.

Provide enough bunk space so timid cows can eat. Dominant animals will push others off, and sorting increases as space gets tight.

Pests, birds and housekeeping

Rodents and birds eat and foul feed, and they can spread disease. Keep feed areas tidy, store commodities in sealed bins, clean up spills, and control pests with methods your vet and local specialists approve. Don't leave open bags or piles around.

To tell whether your steps work, track shrink. Compare feed harvested or purchased with feed fed, accounting for dry matter. Track refusals and mixer variation. Revisit the numbers after changes, and set a simple target to improve.

Extension resources at extension.org can help you set up a shrink calculation. A farm that cuts waste even a little can feed the same herd on less purchased feed, or hold a bit more inventory against a bad year.

Put a number on it once, even roughly. Weigh refusals for a week, check a sample of the silage face for spoiled material, and compare feed purchased with feed delivered to the bunk. The total usually surprises people, and it makes the case for spending an afternoon on a better cover or a tighter face.

Walk the feed path once a week from storage to bunk, looking for anything that spills, spoils or sits. You'll find the leak faster than any report will.